Spirax Valve

Product Details:

Product Details:

The TD3-3 is a medium pressure thermodynamic steam trap fitted between unions for ease of replacement. Tail pieces are prepared for butt weld ends.

Product Details:

Our company holds immense experience in this domain and is involved in offering a wide assortment ofSpirax Thermodynamic Steam Trap Valve.

Product Details:

Carbon Steel/Stainless Steel Flanged "Y" Strainer - Class 150. ... 3/64" perforated type 304 stainless steel are supplied as standard on sizes 2" to 3". 1/8" perforated type304 stainless steel are supplied as standard on sizes 4" and larger. Other meshes, perforations and materials are available upon request

Product Details:

Safe operation of these products can only be guaranteed if they are properly installed, commissioned, used and maintained by qualified personnel (see Section 1.11) in compliance with the operating instructions. General installation and safety instructions for pipeline and plant construction, as well as the proper use of tools and safety equipment must also be complied with. 1.1 Intended use Referring to the Installation and Maintenance Instructions, name-plate and Technical Information Sheet, check that the product is suitable for the intended use/application. The products listed below comply with the requirements of the European Pressure Equipment Directive 97/23/EC and carry the mark when so required. The products fall within the following Pressure Equipment Directive categories: Product Group 2 Gases Group 2 Liquids FT14 and FT14HC 1"HC, 1¼" and 1½" SEP SEP 2" 1 SEP i) The products have been specifically designed for use on steam, air or water/ condensate which are in Group 2 of the above mentioned Pressure Equipment Directive. The products’ use on other fluids may be possible but, if this is contemplated, Spirax Sarco should be contacted to confirm the suitability of the product for the application being considered. ii) Check material suitability, pressure and temperature and their maximu

Product Details:

Safe operation of this product can only be guaranteed if it is properly installed, commissioned, used and maintained by qualified personnel (see Section 1.11) in compliance with the operating instructions. General installation and safety instructions for pipeline and plant construction, as well as the proper use of tools and safety equipment must also be complied with. 1.1 Intended use Referring to the Installation and Maintenance Instructions, name-plate and Technical Information Sheet, check that the product is suitable for the intended use / application. This product complies with the requirements of the European Pressure Equipment Directive 97 / 23 / EC and falls within category 'SEP'. It should be noted that products within this category are required by the Directive not to carry the mark. i) This product has been specifically designed for use on steam, air or condensate / water, which is in Group 2 of the above mentioned Pressure Equipment Directive. The products’ use on other fluids may be possible but, if this is contemplated, Spirax Sarco should be contacted to confirm the suitability of the product for the application being considered. ii) Check material suitability, pressure and temmperature and their maximum and minimum values. If the maximum operating limits of the product are lower than those of the system in which it is being fitted, or if malfunction of the product could result in a dangerous overpressure or overtemperature occurrence, ensure a safety device is included in the system to prevent such over-limit situations. iii) Determine the correct installation situation and direction of fluid flow. iv) Spirax Sarco products are not intended to withstand external stresses that may be induced by any system to which they are fitted. It is the responsibility of the installer to consider these stresses and take adequate precautions to minimise them. v) Remove protection covers from all connections and protective film 

Product Details:

The pressure reducing valve (PRV) maintains a steady pressure on the downstream side of the control valve. The pressure reducing valve effectively absorbs all changes in resistance due to the changes in flow (volume ≈ √ΔP) and control valve position.

Product Details:

The y strainer purpose is to remove unwanted particles from steam, gas, or liquid using a straining element typically made of wire mesh. Using this mechanical process in pipelines helps to protect everything from pumps to steam traps. Y strainers are sometimes designed with “blow-off valves” to make the cleaning process easier.

Product Details:

Y-Strainers are devices for mechanically removing unwanted solids from liquid, gas or steam lines by means of a perforated or wire mesh straining element. They are used in pipelines to protect pumps, meters, control valves, steam traps, regulators and other process equipment.

Product Details:

Our company has gained name and fame in presenting Spirax Compressed Air Drain Trap Valve.

Product Details:

Our company is the foremost in offering Spirax Ball Float Steam Trap FT14.